1 nic components corp. www.niccomp.com www.lowesr.com www.rfpassives.com www.smtmagnetics.com specifications are subject to change surface mount solid polymer aluminum electrolytic capacitors npc series characteristics standard products and specifications ? low impedance & esr at high frequency ? high ripple current ? replaces multiple tantalum chips in power supplies ? fits eia (7343) ?d? land patterns ? pb-free (gold termination plating) ? compatible with +260c* reflow soldering rated working range 2.0 ~ 10vdc rated capacitance range 22 ~ 470 f operating temperature range -55 ~ +105c capacitance tolerance 20% (m) max. leakage current ( a) after 5 minutes (+20c) <0.04cv surge voltage (1000 cycles, 30 sec. on, 5 min. 30 sec. off, 1k ) working voltage (vdc) 2.0 2.5 4.0 6.3 8.0 10 surge voltage (vdc) 2.6 3.2 5.2 8.2 10.4 11.5 max. tan , 120hz, +20c d1, d6 <0.05 d5 , d7, d8 <0.1 high temperature load life 2,000 hours @ 105c at rated working voltage after 2x recommended re ow pro le capacitance change within 20% of initial measured value tan d7, d8 less than 150% of speci ed max. value d1, d5 , d6 less than 200% of speci ed max. value leakage current less than speci ed max. value moisture resistance 500 hours @ +60c at 90 ~ 95% rh and no voltage applied after 2x recommended re ow pro le (jedec msl-3) capacitance change within -20%/+40% of initial measured value d5 , *within -20%/+60% of initial measured value tan d7, d8 less than 150% of speci ed max. value d1, d5 , d6 less than 200% of speci ed max. value leakage current less than 300% of speci ed max. value nic part number (+260c re ow) wv cap. max. lc tan max. ripple current (marms) 100khz @ +105c max. esr +20c & 100khz ( ) height h 0.1 (vdc) ( f) ( a) npc101m2d5zatrf 2 100 8.0 0.10 2,700 0.009 1.1 npc101m2d1uatrf 100 8.0 0.05 3,000 0.005 1.4 npc101m2d1zatrf 100 8.0 0.05 3,000 0.009 1.4 npc101m2d6xatrf 100 8.0 0.05 3,000 0.013 1.9 npc101m2d6zatrf 100 8.0 0.05 3,000 0.009 1.9 npc121m2d6zatrf 120 9.6 0.05 3,000 0.009 1.9 npc151m2d5zatrf 150 12.0 0.10 2,700 0.009 1.1 npc151m2d1uatrf 150 12.0 0.05 3,000 0.005 1.4 npc151m2d6zatrf 150 12.0 0.05 3,000 0.009 1.9 npc181m2d5zatrf 180 14.4 0.10 2,700 0.009 1.1 npc181m2d6zatrf 180 14.4 0.05 3,000 0.009 1.9 npc221m2d5zatrf 220 17.6 0.10 2,700 0.009 1.1 npc221m2d6yatrf 220 17.6 0.05 3,000 0.007 1.9 npc221m2d6zatrf 220 17.6 0.05 3,000 0.009 1.9 npc221m2d7xatrf 220 17.6 0.10 3,500 0.010 2.7 npc271m2d6zatrf 270 21.6 0.05 3,000 0.009 1.9** npc271m2d6yatrf 270 21.6 0.05 3,500 0.006 1.9** npc271m2d8yatrf 270 21.6 0.10 3,500 0.007 2.9 npc331m2d6zatrf* 330 26.4 0.10 3,000 0.009 1.9** npc331m2d6yatrf* 330 26.4 0.10 3,500 0.006 1.9** npc331m2d6uatrf* 330 26.5 0.10 3,500 0.0045 1.9** npc331m2d8yatrf 330 26.4 0.10 3,500 0.007 2.9 npc391m2d8yatrf 390 31.2 0.10 3,500 0.007 2.9 npc471m2d8yatrf 470 37.6 0.10 3,500 0.007 2.9 npc820m2.5d1zatrf 2.5 82 8.2 0.05 3,000 0.009 1.4 npc820m2.5d6xatrf 82 8.2 0.05 3,000 0.013 1.9 npc820m2.5d6zatrf 82 8.2 0.05 3,000 0.009 1.9 npc101m2.5d5zatrf 100 10.0 0.10 2,700 0.009 1.1 npc101m2.5d1uatrf 100 10.0 0.05 3,000 0.005 1.4 features *see part number system for details pnbs fdil rohs compliant includes all homogeneous materials *see note regarding df in characteristics table (moisture resistance). **height dimension tolerance 0.2mm *applies to values with asterisk in column "nic part number"
2 nic components corp. www.niccomp.com www.lowesr.com www.rfpassives.com www.smtmagnetics.com specifications are subject to change nic part number (+260c re ow) wv cap. max. lc tan max. ripple current (marms) 100khz @ +105c max. esr +20c & 100khz ( ) height h 0.1 (vdc) ( f) ( a) npc101m2.5d6zatrf 2.5 100 10.0 0.05 3,000 0.009 1.9 npc121m2.5d1uatrf 120 12.0 0.05 3,000 0.005 1.4 npc121m2.5d6zatrf 120 12.0 0.05 3,000 0.009 1.9 npc151m2.5d5zatrf 150 15.0 0.10 2,700 0.009 1.1 npc151m2.5d6zatrf 150 15.0 0.05 3,000 0.009 1.9 npc181m2.5d5zatrf 180 18.0 0.10 2,700 0.009 1.1 npc181m2.5d6zatrf 180 14.4 0.05 3,000 0.009 1.9 npc181m2.5d7xatrf 180 18.0 0.10 3,500 0.010 2.7 npc221m2.5d6yatrf* 220 22.0 0.10 3,500 0.006 1.9** npc221m2.5d6zatrf* 220 22.0 0.10 3,000 0.009 1.9** npc221m2.5d8yatrf 220 22.0 0.10 3,500 0.007 2.9 npc271m2.5d6zatrf* 270 27.0 0.10 3,000 0.009 1.9** npc271m2.5d6yatrf* 270 27.0 0.10 3,500 0.006 1.9** npc271m2.5d8yatrf 270 27.0 0.10 3,500 0.007 2.9 npc331m2.5d8yatrf 330 33.0 0.10 3,500 0.007 2.9 npc391m2.5d6yatrf** 390 39.0 0.10 3,500 0.006 1.9** npc391m2.5d8zatrf 390 39.0 0.10 3,500 0.009 2.9 npc680m4d5xatrf 4.0 68 10.9 0.10 2,100 0.015 1.1 npc680m4d1zatrf 68 10.9 0.05 3,000 0.009 1.4 npc680m4d6xatrf 68 10.9 0.05 3,000 0.013 1.9 npc680m4d6zatrf 68 10.9 0.05 3,000 0.009 1.9 npc820m4d6xatrf 82 13.1 0.05 3,000 0.010 1.9 npc101m4d6xatrf 100 16.0 0.05 3,000 0.010 1.9 npc121m4d6xatrf 120 19.2 0.05 3,000 0.010 1.9 npc151m4d6xatrf 150 24.0 0.05 3,000 0.010 1.9 npc151m4d7xatrf 150 24.0 0.10 3,500 0.010 2.7 npc181m4d6zatrf 180 28.8 0.05 3,000 0.009 1.9** npc181m4d8zatrf 180 28.8 0.10 3,500 0.009 2.9 npc221m4d6zatrf 220 35.2 0.05 3,000 0.009 1.9** npc221m4d8zatrf 220 35.2 0.10 3,500 0.009 2.9 npc271m4d8zatrf 270 43.2 0.10 3,500 0.009 2.9 npc330m6.3d6xatrf 6.3 33 8.3 0.05 3,000 0.013 1.9 npc470m6.3d5xatrf 47 11.8 0.10 2,100 0.015 1.1 npc470m6.3d1xatrf 47 11.8 0.05 3,000 0.010 1.4 npc470m6.3d6xatrf 47 11.8 0.05 3,000 0.013 1.9 npc470m6.3d6zatrf 47 11.8 0.05 3,000 0.009 1.9 npc560m6.3d6xatrf 56 14.1 0.05 3,000 0.010 1.9 npc680m6.3d6xatrf 68 17.1 0.05 3,000 0.010 1.9 npc820m6.3d6xatrf 82 20.7 0.05 3,000 0.010 1.9 npc101m6.3d6xatrf 100 25.2 0.05 3,000 0.010 1.9 npc101m6.3d7xatrf 100 25.2 0.10 3,500 0.010 2.7 npc121m6.3d6zatrf* 120 30.2 0.05 3,000 0.009 1.9** npc121m6.3d8zatrf 120 30.2 0.10 3,500 0.009 2.9 npc151m6.3d6zatrf 150 37.8 0.05 3,000 0.009 1.9** npc151m6.3d8zatrf 150 37.8 0.10 3,500 0.009 2.9 npc181m6.3d8zatrf 180 45.4 0.10 3,500 0.009 2.9 npc221m6.3d8zatrf 220 55.4 0.10 3,500 0.009 2.9 npc150m8d6xatrf 8 15 4.8 0.05 3,000 0.015 1.9 npc220m8d6atrf 22 7.0 0.05 2,500 0.018 1.9 npc330m8d6atrf 33 10.6 0.05 2,500 0.018 1.9 npc330m8d7xatrf 33 10.6 0.10 3,000 0.013 2.7 npc470m8d6atrf 47 11.8 0.05 2,500 0.018 1.9 npc680m8d7atrf 68 21.8 0.10 2,500 0.018 2.7 npc101m8d7atrf 100 32.0 0.10 2,500 0.018 2.7 npc220m10d6atrf 10 22 8.8 0.10 1,600 0.030 1.9 npc470m10d6atrf 47 18.8 0.10 1,800 0.025 1.9 surface mount solid polymer aluminum electrolytic capacitors npc series standard products and specifications frequency 1khz<=f<10khz 10khz<=f<100khz 100khz<=f<1mhz correction factor 0.6 0.85 1.0 ripple current frequency correction factors *see note regarding df in characteristics table (moisture resistance). **height dimension tolerance 0.2mm
3 nic components corp. www.niccomp.com www.lowesr.com www.rfpassives.com www.smtmagnetics.com specifications are subject to change recommended land patterns (mm) case code abc d1, d5 , d6, d7, d8 2.4 2.9 3.7 a b c a surface mount solid polymer aluminum electrolytic capacitors npc series notes on reflow soldering : 1. sac alloy (+217c) re ow soldering compatible 2. soldering heat limits apply to the top surface of component 3. if you have concerns about your re ow soldering pro le review them with nic to insure compatible [tpmg@niccomp.com] application notes: 1. npc series cannot be used in coupling, time-constant or other circuits that are greatly affected by leakage current. 2. npc parts are polarized so be sure to verify component orientation when mounting components. 3. do not apply over voltage exceeding the rated voltage. 4. do not apply ripple current over the speci ed maximum ripple current rating. time (seconds) component surface temp. ( o c) recommended reflow soldering profile pre-heat 160 o c ~ 180c natural cooling peak temperature 260c max. for 10 sec. 120 sec. max. 250 230 160 100 50 200 time above 230c 40 sec. max. 30 sec. max. 260 termination material: au: 0.003 ~ 0.014 m pd: 0.02 ~ 0.07 m ni: 0.5 ~ 2.0 m ni: 0.5 ~ 2.0 m pd: 0.02 ~ 0.07 m au: 0.003 ~ 0.014 m cu: 100 8 m dimensions (mm) voltage codes voltage code 2.0vdc d 2.5vdc e 4.0vdc g 6.3vdc j 8.0vdc k 10vdc a case code l 0.2 w 0.2 h 0.1 w1 0.1 s 0.2 d1 7.3 4.3 1.4 2.4 1.2 d5 1.1 d6 1.9* d7 2.7 d8 2.9 w1 + 220 d58 anode polarity indicator voltage code capacitance value lot number w h l s part numbering system npc 101 m 6.3 d7 x a tr 500 f rohs compliant optional 500 piece reel qty tape & reel packaging denotes +260c peak re ow performance code (see standard products & speci cations tables) case size working voltage (vdc) tolerance code m=20%, k=10% capacitance code in f, rst 2 digits are signi cant, third digits no. of zeros series *d6 - see standard products & speci cations tables for height tolerance. w 1
4 nic components corp. www.niccomp.com www.lowesr.com www.rfpassives.com www.smtmagnetics.com specifications are subject to change tape dimensions (mm) reel tape dimensions (mm) c a w b t case code a 0.1 b 0.2 c 0.3 d 0.05 e 0.1 f 0.1 g 0.05 h 0.1 j -0/+0.1 k 0.1 t 0.05 d1 4.50 7.70 12.0 5.5 1.75 8.0 2.0 4.0 1.5 1.6 0.3 d5 1.5 d6 2.2 d7 2.9 d8 3.1 case code a 2.0 b 1.0 c 0.2 w 1.0 t 0.5 reel quantity d1, d5 , d6 330 80 13 13.5 2.0 3,500 500* d7, d8 2,000 d j f t k c a h e b g *see part number system for details on designating reel quantity surface mount solid polymer aluminum electrolytic capacitors npc series precautions please review the notes on correct use, safety and precautions found on pages t10 & t11 of nic?s electrolytic capactitor catalog . also found at www.niccomp.com/precautions if in doubt or uncertainty, please review your speci c application - process details with nic?s technical support personnel: tpmg@niccomp.com + 220 d58 + 220 d58 + 220 d58 anode
|
